THE NEW EU PACKAGING AND PACKAGING WASTE REGULATION

The new European Union Packaging and Packaging Waste Regulation (EU 2025/40) officially became applicable on 12 August 2026, with increased responsibilities and costs. Elaine Campling, Chair of ESMA Health, Safety and Environmental Protection Committee, reports.

The regulation applies to all packaging and packaging waste: “This Regulation applies to all packaging, regardless of the material used, and to all packaging waste, whether such packaging is used in or such packaging waste originates from industry, other manufacturing, retail or distribution, offices, services or households”. 

The overall aim of the regulation is to achieve a 15% waste reduction by 2040 (compared to 2018 levels), and also to ensure that all packaging placed on the EU market is fully recyclable by 2030. Waste reductions targets are 5% by 2030, 10% by 2035, with the 15% target achieved by 2040. 

Key elements of the regulation are provided below, which are generally subject to transitional implementation. 

Recyclability
All packaging must be recyclable by 2030 and must be achievable in an economically viable way. Packaging is considered recyclable if it means two conditions: 
(a) It is designed to enable the use of resulting secondary raw materials that are of sufficient quality when compared to the original material to substitute primary raw materials; 
(b) It can be collected separately when it becomes waste, sorted into specific waste streams without affecting the recyclability of other waste streams and recycled at scale. 
Packaging recyclability will be expressed by performance grades. 

Labelling 
Harmonised recycling symbols will apply to facilitate consumer sorting. The label is required to be based on pictograms and be easily understood. With the exception of e-commerce packaging, this obligation does not apply to transport packaging or packaging that is subject to a deposit and return system. 

Substances of concern 
Packaging placed on the market that contains substances of concern (SoC) is required to be marked to identify this. The European Chemicals Agency has prepared a draft list of around 700 candidate substances. A report on SoC is expected to be made available by the end of the year. However, PFAS restrictions in food contact packaging are already in force. 

Registration 
Each Member State is required to establish a national register to monitor requirements. Producers will be obligated to register in each Member State where they make packaging or packaged products available for the first time, or where they unpack packaged products without being end users. This obligation may be made on behalf of producers by an authorised representative. 

Documentation 
Essential documents include a Declaration of Conformity and technical information. The technical documentation must support the packaging description and intended use, the conceptual design and materials used in the packaging, harmonised standards, common specifications, technical specifications and test reports. 

Fees 
Competent Authorities will be able to charge cost-based, ‘proportionate’ fees. Fees are expected to increase costs by 30 to 60% between 2027 and 2030 across most material categories, due to rising recycling targets, higher waste-treatment costs, and incoming carbon-based fee components. 

Importers/Distributors 
Importers must ensure that the packaging they place on the market complies with requirements and that documentation drawn up by manufacturers is available for inspection by the competent national authorities. When placing packaging on the market, every importer must include their name, registered trade name or registered trademark on the label, postal address and electronic means of communication, where available. Distributors are required to ensure their handling of the packaging does not adversely affect compliance with requirements. 
Any importer or distributor that places packaging on the market under their own name or trademark or modifies packaging already placed on the market in a way that could affect compliance with the regulation, will be considered the manufacturer and assume responsibility for manufacturer obligations. 

Please join us at HSEP committee meetings for discussions on PPWR, CLP, REACH, Digital Product Passport, EU Green Deal, and other important topics. Check next meeting dates at esma.com/committees/hsep

ESMA: Connecting the Dots of the Printing Industry

  • IPI
  • GlassPrint
  • ESMA Academy
  • HSEP
  • TPS
  • 1

ESMA Newsletter

Please select at least one mailing from the list below

By subscribing you agree with our privacy policy

Supporting

Member of

AIPIA

ETP

Contact

ESMA
Kraasbeekstraat 3
B-3390 Tielt-Winge, Belgium

Peter Buttiens [ESMA General Manager]

  This email address is being protected from spambots. You need JavaScript enabled to view it.
  + 32 (0)16 894 353